Jiangsu milky way steel poles co.,ltd
Jiangsu Milky Way Steel Poles Co.,Ltd We Focous on High Quality
Add to Cart
Round 69kv 10m 3mm thickness joint type Steel Utility Pole for Electrical Distribution With double cross arm
Specifications:
| series | Outside Diametar | Wall Thicness |
| mm | Min. | mm /SWG |
| 15 L | 21.3 | 2 |
| M | 2.6 | |
| H | 3.2 | |
| 20 L | 26.9 | 2.3 |
| M | 2.6 | |
| H | 3.2 | |
| 25 L | 33.7 | 2.6 |
| M | 3.2 | |
| H | 4 |
Production Control
10 Reasons That Steel Poles Make Sense According to research, here are the primary reasons wooden and concrete utilities are switching to Steel Utility Pole:
o Easy to Handle
o Light Weight
o Long Life
o Cost Effective
o Low Maintenance
o Sustainable
o Durable
o Safe
o Aesthetics
o Engineered for Strength
Application:
Transmission Applications
Light Duty Steel Poles
Custom Design Transmission Poles
Steel H-Frame Poles
Substation Applications
Dead End Structures
A-Frames and H-Frames
Special Application Structures
Low Side Supports – Buss, Switch, and Other equipment
Static and Shield Wire Poles
Design:
Standard Accessory
-Top plate
-Base plate
-Bottom strip
-Standard hole
-Climbing rung
-Anchor bolt
-Bitumen protection
-Painted marking
-Removable ladder
Available Foundation Types
Direct Embedment
Anchor Bolt/Base Plate
Vibratory Steel Caisson
Available Finishes
Galvanized per ASTM A123
Paint over galvanized,paint over black steel
Powder Coating
Standard Features
In-Ground Mounted:
12-sided pole shaft
Welded top cap
Mounting holes (to your specification if required)
Identification plate
M12 earth point 250mm above the nominal ground line
M24 nut 250mm above the nominal ground line (to assist lifting)
Additional in-ground corrosion protection 200mm above to 400mm below the nominal ground line
Anti-sink straps
Hot dip galvanised finish
Base Plate Mounted:
12-sided pole shaft (40kN to 80kN)
16-sided pole shaft (100kN & 120kN)
Welded top cap
Mounting holes (to your specification if required)
Identification plate
M12 earth point 250mm above the pole base
Two lifting gussets on the base plate
Anchor bolts, templates, nuts & washers
Hot dip galvanised finish
Transmission Structures
Steel Tapered Poles for Transmission Structures
H-frames Power Pole DesignsVariety of Finishes for and Utility Pole Structures
Smaller Diameter Light Steel Structures (Sidewalks and Tight Right-of-Ways)
Custom Design Matching to Wood Pole Classifications
Custom Pole Designs
Wood equivalent Steel Power Pole Configuration for Short Lead Times or Repair Jobs
Antenna Tower Structures
Patented Splice Joints for Steel Structures
Traditional Flange Splices for Steel Structures
Cell Tower Structures
Lattice Design Structures
I-Beam Structures
Pre-Drilled Power Pole Apparatus Using Plasma Burning Process
Self-Conducting Stainless Steel Utility Poles for Grounding Purposes
Hardware for Light Poles
Pre-drilled Holes for Safety Steps and Equipment
No Extra Welding is Needed for Conductor Hookups to Attach Transmission Lines
Single Circuit Line Hookup for Utility Pole Structures
Double Circuit Line Hookup for Utility Pole Structures
Shield Wire Guards to Protect Against Lightning
Substation Structures
Tapered Tubular Substation Structures
Steel Substation Structures
Custom Substation Designs
Closed Section Tubes
I-Beam Structures
Lattice Structures
Steel Structures with Higher Translational Stiffness
Low Profile Aesthetically Pleasing Structures
Higher Terminal-Stop/Take Off Angles
Higher Tension Wires Due to Design
Substation Structures Exceed Wood Pole Standards